V8910-BK-LMS-ESD
PEN-VAC PRO SERIES black body, probes (1) bent (1) straight each with 1/8" ((3.18mm), 1/4" (6.35mm) and 3/8" (9.53mm) diametermeter conductive silicone vacuum cups.
The PEN-VAC is totally self-contained. There are no batteries or hoses to get in the way. Operation is as follows:
1. Select a tip with a rubber vacuum cup on a probe that is slightly smaller than the part you want to pick and place. Put the probe snuggly on the tip of the vacuum pen. Make sure that there is no dust on the rubber vacuum tip. NOTE: Our larger rubber vacuum cups can be placed directly on the vacuum pen tip without using a probe.
2. Depress AND hold the button on the side of the tool.
3. Touch the vacuum tip squarely to the part and release the button. The part is now grasped.
4. Move the part to where you want it and depress the button again. The part is now released.
NOTE: This tool works only with the rubber vacuum tips. The rubber is required for an air-tight seal.
Pen-Vac Pro系列黑色機身，探頭（1）彎曲（1）筆直，每個帶有1/8”（（3.18mm）、1/4”（6.35mm）和3/8”（9.53mm）直徑的導電硅真空杯。
PEN-VAC是完全獨立的。沒有電池或軟管阻擋。操作如下：
1。選擇一個探針上帶有橡膠真空杯的尖端，該探針略小于要拾取和放置的零件。把探針緊貼在真空筆的頂端。確保橡膠真空吸嘴上沒有灰塵。注意：我們較大的橡膠真空杯可以直接放在真空筆頭上，而不用探針。
2。按住工具側(cè)面的按鈕。
三。將真空吸嘴垂直接觸零件并松開按鈕?，F(xiàn)在抓住了這一部分。
4。將部件移動到所需位置，然后再次按下按鈕。零件現(xiàn)在釋放。
注意：此工具僅適用于橡膠真空吸嘴。密封需要橡膠。
PEN-VAC PRO SERIES black body, probes (1) bent (1) straight each with 1/8" ((3.18mm), 1/4" (6.35mm) and 3/8" (9.53mm) diametermeter conductive silicone vacuum cups.
The PEN-VAC is totally self-contained. There are no batteries or hoses to get in the way. Operation is as follows:
1. Select a tip with a rubber vacuum cup on a probe that is slightly smaller than the part you want to pick and place. Put the probe snuggly on the tip of the vacuum pen. Make sure that there is no dust on the rubber vacuum tip. NOTE: Our larger rubber vacuum cups can be placed directly on the vacuum pen tip without using a probe.
2. Depress AND hold the button on the side of the tool.
3. Touch the vacuum tip squarely to the part and release the button. The part is now grasped.
4. Move the part to where you want it and depress the button again. The part is now released.
NOTE: This tool works only with the rubber vacuum tips. The rubber is required for an air-tight seal.
Pen-Vac Pro系列黑色機身，探頭（1）彎曲（1）筆直，每個帶有1/8”（（3.18mm）、1/4”（6.35mm）和3/8”（9.53mm）直徑的導電硅真空杯。
PEN-VAC是完全獨立的。沒有電池或軟管阻擋。操作如下：
1。選擇一個探針上帶有橡膠真空杯的尖端，該探針略小于要拾取和放置的零件。把探針緊貼在真空筆的頂端。確保橡膠真空吸嘴上沒有灰塵。注意：我們較大的橡膠真空杯可以直接放在真空筆頭上，而不用探針。
2。按住工具側(cè)面的按鈕。
三。將真空吸嘴垂直接觸零件并松開按鈕?，F(xiàn)在抓住了這一部分。
4。將部件移動到所需位置，然后再次按下按鈕。零件現(xiàn)在釋放。
注意：此工具僅適用于橡膠真空吸嘴。密封需要橡膠。